![]() However, if you would like to run it using the switch then please follow the next steps. If you would like a simple installation, you can directly connect the white wire to the desired fuse slot so the fog lights will automatically turn on once the vehicle is on. You will save yourself the hassle from needing a battery jump start for a dead battery. We advise locating a fuse that has power supplied when the vehicle is turned on because it will prevent the fog lights staying on accidentally once you leave your vehicle. You may need to get some additional 16-18 gauge wire to extend the wire to reach the interior of the vehicle. Once you have located the fuse, there is a red wire from the power switch (included in the Scion FR-S fog light kit) that would need to be tapped into the fuse. In this step, you will need a test light or power probe to assist you in locating which fuse slot provides power when the vehicle is on. See Accessories for more information on fog lamps.Īddendum, : Circuit with additional relay for Dual Fog Lamps.You will need to remove the fuse box cover located on the passenger side of the Scion FR-S. Any maintenance would require the usual double-jointed arms, or removal of the grille. The relay is screwed to the shelf, but space is tight. The relay has a riveted mount with two screw holes. I chose not to do that, and covered the extra connector with shrink-tube. >"The relay is a 6RA, sealed, with four plug-in (spade) connectors." The load terminal is actually a double connector so you could in theory plug both fog lamp wires directly in. The result looks very clean, the lights are nice and bright, no worries about wires melting if I get a short, and after 20 years I finally have fog lamps on the car.Īt 11:06 AM 9/23/04 -0700, Mark L. Install the plastic fog light cover by screwing it into place. Position the metal brackets (that hold the fog light) into these cut-out sections, and screw them in place. This mimics the headlamp wiring and follows my rather sketchy factory install instructions.ġ0) Same thing on the driver's side, but the wires are connected to the harness wires in (8), each with a single bullet connector. Step 3 Install fog light brackets and re-install bumper. Red/yellow wire connected to the double bullet connector in (4), black wire to the double bullet connector in (7). Harness followed the headlamp harness routing over to the driver's side.ĩ) On the passenger's side, 14-strand red/yellow wire and black wire in a PVC sleeve (matches headlamp pigtail wiring sleeve) from the fog lamp, down the back of the bumper overrider, through a 3/8" hole in the valance (protected with a grommet), and up through the hole for the headlamp wiring entrance into the engine bay. The black wire is connected to the double bullet connector in (7). Step 2: Spray and Lubricate Fog Light Lenses Step 3: Remove Liner from Fog Light Tints Step 4: Align and Apply DRL Tint Step 5: Spray Your Daytime Running. The red/yellow wire is connected to the double bullet connector in (4). The wire is cable-tied to the harness that runs behind the large diameter fresh air intake hose, routed through the same radiator wall grommet that the harness uses, and is completely hidden.Ĥ) Red/yellow 28-strand wire from the relay's load terminal to a double bullet connector.ĥ) Existing harness's red/yellow 14-strand wire connected to the relay switch terminal.Ħ) A 14-strand black ground wire from the relay ground terminal to a local fender bolt.ħ) A 28-strand black ground wire from the same fender bolt to a double bullet connector.Ĩ) A 33" braided harness containing a red/yellow and a black wire to run power and ground over to the driver's side lamp. If I ever have problems with the relay, access will be painful, but not impossible.ģ) Brown 28-strand wire from the starter terminal to an inline fuse, and brown/white 28-strand wire from there to the relay power terminal. This meant removing the grille for access, but resulted in a clean look. Following is a brief summary."ġ) Two Lucas SFT-576 fog lamps on chrome mounting brackets bolted to the bumper behind the overriders.Ģ) A Lucas 4-terminal relay mounted on the radiator shelf, passengers side, near the harness connections to the headlamps. >"You gave me some useful advice a couple of months ago about installing fog lamps, and a couple of weeks ago when I finally had some free time, I completed the installation.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |